The crown margin looks clear in the mouth. Why does part of it disappear on the scan? If the distal finish line fades into the gingiva on screen, compare that area with what you see clinically before deciding whether to reach for a bur or rescan.
Why is my crown margin missing on the intraoral scan?
A crown margin can look incomplete on an intraoral scan when soft tissue, saliva, or blood obscures the finish line, or when the scanner has limited access to that area. An irregular finish line on the tooth can also look irregular on the scan. Check the preparation directly, correct the cause you find, then confirm that the entire margin is visible on the final scan.
What to check when a crown margin looks unclear
|
What you see |
What to check first |
Next step |
|
A jagged edge or a visible step |
Can you see the same irregularity on the tooth? |
Refine the area if the defect is in the preparation. If it appears only on screen, check scan coverage and visibility. |
|
A missing mesial or distal segment |
Can the scanner reach the area from another angle? Is tissue or fluid obscuring the margin? |
Restore visibility and recapture the area from an angle that shows the finish line. |
|
The finish line blends into the gingiva |
Is soft tissue covering the margin? |
Use appropriate gingival displacement to expose the finish line before scanning again. |
|
A void or fuzzy patch near the margin |
Is the area contaminated with saliva or blood, or is the scan incomplete? |
Clear the field, control bleeding as needed, and inspect the new capture. |
1. Check whether the finish line needs refinement
Inspect the margin directly under magnification and compare it with the same spot on the scan. If the tooth has a local step or an uneven transition, refine that area while preserving the intended margin geometry. For light refinement of an established finish line, the kit includes the MR.BUR 36F fine-grit taper-round diamond bur.
In a 2026 laboratory study, fine-grit diamond finishing improved scan trueness and precision on dry dentin. The researchers found no significant improvement on dry enamel. Use that finding to inform the finishing step and verify the margin on the scan regardless of which bur you use.
Earlier in the preparation, the S6Z super-coarse taper-round diamond bur is an option for initial bulk reduction. If the preparation itself needs controlled interproximal opening, the kit includes the 52 coarse pointed-cone diamond bur. A gap on screen alone is a reason to inspect the area clinically before removing more tooth structure.
2. Expose the margin and control moisture
If the finish line is continuous clinically but disappears on screen, look for tissue overlap, saliva, and bleeding before refining the preparation further. In a laboratory study with two intraoral scanners, subgingival finish lines showed larger scan discrepancies than equigingival finish lines. Saliva increased discrepancies at all margin depths tested.
Use gingival displacement when indicated, clear excess fluid, and control bleeding before capture. The practical check is whether you can see the entire finish line, especially in proximal areas and where the margin extends below the gingiva. If the tissue keeps covering the margin or bleeding persists, reassess the field before taking the definitive scan.
3. Trace the finish line on screen before sending the scan
-
Rotate the scan. Inspect the preparation from multiple angles, including the proximal surfaces.
-
Follow the finish line all the way around. Zoom in wherever the edge looks blurred or merges with the gingiva. Compare color and monochrome views if your software offers both. Color helped identify the finish line on several scanners in one laboratory comparison.
-
Recheck the area after a correction. If a segment is still unclear, compare it with the tooth, address the cause, and use your scanner’s recapture workflow. Review the complete margin again before sending the scan to the lab.
Chairside example. The distal margin of a molar fades into the gingiva on the scan. In the mouth, the finish line is continuous, but a fold of tissue partly covers it. Expose the margin, clear the field, and recapture the distal area. Then rotate the scan to confirm that you can follow the finish line from the buccal side around the distal surface to the lingual side.
How does a digital crown scan differ from a conventional impression?
An intraoral scanner needs a clear view of the finish line. A conventional impression records the area through physical contact with impression material. In both workflows, manage tissue and moisture and inspect the result chairside. On a digital scan, look for missing or indistinct margin segments. On a conventional impression, look for incomplete detail, tears, pulls, and voids.
Frequently asked questions
Can I scan a subgingival crown margin?
Yes, if the finish line can be exposed and captured clearly. Deeper margins and saliva make capture more challenging. The clearance needed can vary with the margin depth and scanner, so verify the result on screen.
Should I use a finishing bur if the margin looks blurry?
First, inspect the same area on the tooth. A fine-grit diamond can help refine an uneven finish line. If the line is already continuous and the blur appears only on screen, start by checking tissue coverage, moisture, and scanner access.
For bur selection from initial reduction to final refinement, explore the MR.BUR Crown & Bridge Preparation Kit FG. For more on clearance, taper, and preparation geometry, see MR.BUR’s zirconia crown preparation guide.
Diamond Burs, Carbide Burs, Surgical & Lab Use Burs, Endodontic burs, IPR Kit, Crown Cutting Kit, Gingivectomy Kit, Root Planning Kit, Orthodontic Kit, Composite Polishers, High Speed Burs, Low Speed Burs



